• Facebook
  • Twitter
  • Youtube
Where to buy the Enduro EVO RDM C60
Specifications
  DESIGNATION WEIGHT  [TOLERANCE] TYPE IMCS STIFNESS BEND CURVE BASE % TOP %
label_hardtop.jpg Enduro EVO RDM C60 hard top 340 1,70 [+/- 5%] HARD TOP 15 10,5 64,5% 75,0%
Enduro EVO RDM C60 hard top 370 1,85 [+/- 5%] HARD TOP 17 10,5 64,5% 75,0%
Enduro EVO RDM C60 hard top 400 2,05 [+/- 5%] HARD TOP 19 10,5 64,5% 75,0%
Enduro EVO RDM C60 hard top 430 2,30 [+/- 5%] HARD TOP 21 10,5 64,5% 75,0%
               
label_cnstcurve.jpg
Enduro EVO RDM C60 const. curve 340 1,70 [+/- 5%] CONSTANT CURVE 15 13 64,0% 77,0%
Enduro EVO RDM C60 const. curve 370 1,85 [+/- 5%] CONSTANT CURVE 17 13 64,0% 77,0%
Enduro RDM EVO C60 const. curve 400 2,05 [+/- 5%] CONSTANT CURVE 19 13 64,0% 77,0%
Enduro EVO RDM C60 const. curve 430 2,30 [+/- 5%] CONSTANT CURVE 21 13 64,0% 77,0%
               
label_flextop.jpg
Enduro EVO RDM C60 flex top 340 1,70 [+/- 5%] FLEX TOP 15 14,5 63,5% 78,0%
Enduro EVO RDM C60 flex top 370 1,85 [+/- 5%] FLEX TOP 17
14,5 63,5% 78,0%
Enduro EVO RDM C60 flex top 400 2,05 [+/- 5%] FLEX TOP 18 14,5
63,5% 78,0%
Enduro EVO RDM C60 flex top 430 2,30 [+/- 5%] FLEX TOP 20 14,5 63,5% 78,0%
FAQ

Which masts do you measure for the data of the Mast selector Matrix Tool?

Mostly we take multiple C100 masts as the reference of various brands, in general those represent the most accurate bend curve of the sails. This is because sail brands design the sails to perform best on those C100 masts.  

We also found quite big differences in tolerances regarding production with all brands. Fluctuations of bend curves and stiffness from +/- 1-2 points (bend curve) which proves that none of the brands are 100% consistent. So we measure several masts per brand and take the average of those measurements into account when constructing the Mast Selector Matrix Tool.   

Why are Unifiber mast's top and bottom pieces different lengths?

We produce the masts on existing mandrels, with integrated ferrules, based on the principle of optimum load distribution, regardless of section length. If we invested in new mandrels - and even matched the current consistency and performance we deliver - then the higher cost of production would impact on the price-to-quality ratio we could offer our customers. If your quiver bag does not fit the longer section, please consider a Unifiber quiver bag that will take the longer bottom piece of masts up to 490.

Can I interchange top and bottom mast pieces of Unifiber masts - for example a 430 bottom with a 400 top?

Because of the integrated ferrule system we use, each top and base match a pre-defined conical shape determined by the optimum load distribution for that model. In production the top is made to fit precisely on the base of the relevant model. Different bend curves alos have different wall thickness as well as varying geometric shapes, so it's technically not possible or advisable to exchange base and top parts.

What is the internal diameter of Unifiber's RDM masts?

Unifiber RDM masts have a 33-mm. internal diameter up to 600 mm. from the base, tapering to 32mm above 600mm

How far into a Unifiber RDM mast does the internal diameter stay the same width?

Unifiber RDM masts stay at a constant 33 mm. internal width up to 600 mm. into the base section. Beyond 600 mm. the internal width tapers to 32 mm.

What's the minimum overlap required for a mast extension inside a Unifiber mast?

Unifiber recommends a minimum of 100 mm. of mast extension to overlap the inside of the mast to prevent stress load damaging the base of the mast.

What level of breaking strain can a Unifiber mast take?

In testing Unifiber masts can endure stress of up to 180 kg.

Why do Unifiber SDM 100% masts cost more proportionally than the 40/60/80% models?

Unifiber's SDM C100 masts have an additional (radial) compression layer for durability reasons, since many brands' C100 masts were breaking due to an increase in luff curve, on race sails especially. As SDM C100s need to be light and durable there are more costly materials used to reach this objective. Without the additional compression layer the durability aspect would be not as good. We are confident you will find our masts perform well in all 3 bend curves.

Reviews - Help us by reviewing our products:

We would like to invite you to post your user experience if you own this product. In case you have any warranty related issue please use our warranty forms. We always keep the right to remove any messages or postings that can cause damage to the image of the brand Unifiber.
We would like to thank you for your contribution.